All Vaild Cisco 642-902 Dumps Offered By Passleader For Free Download (21-30)

QUESTION 21
Refer to the exhibit. EIGRP is enabled on all routers on the network. What additional configuration is required for the routers connected over the Frame Relay multipoint interfaces to compensate for a low-speed NBMA connection?

A.    Configure the EIGRP hello interval on all Frame Relay interfaces to 5 seconds.
B.    Configure the EIGRP hello interval on all Frame Relay interfaces to 60 seconds.
C.    Configure the EIGRP hold time on all Frame Relay interfaces to 15 seconds.
D.    Configure the EIGRP hold time on all Frame Relay interfaces to 180 seconds.
E.    Configure the bandwidth on all EIGRP Frame Relay interfaces to the committed information rate (CIR).
F.    Configure the bandwidth on all EIGRP Frame Relay interfaces to the lowest CIR multiplied by the number of PVCs for the multipoint connection.

Answer: F

QUESTION 22
A network administrator would like to configure an EIGRP router as a stub router that advertises directly connected and summary routes only. What command must the administrator issue to accomplish this?

A.    eigrp stub
B.    eigrp stub connected
C.    eigrp stub summary
D.    eigrp stub connected static
E.    eigrp stub receive-only

Answer: A

QUESTION 23
Refer to the partial configurations in the exhibit. What address is utilized for DR and BDR identification on Router1?

A.    the serial 1/1 address
B.    the serial 2/0 address
C.    a randomly generated internal address
D.    the configured router-id address

Answer: D

QUESTION 24
Which two routing protocols require a metric to be configured when redistributing routes from other protocols? (Choose two.)

A.    RIP
B.    OSPF
C.    EIGRP
D.    IS-IS
E.    BGP

Answer: AC

QUESTION 25
By default, which statement is correct regarding the redistribution of routes from other routing protocols into OSPF? Select the best response.

A.    They will appear in the OSPF routing table as type E1 routes.
B.    They will appear in the OSPF routing table as type E2 routes.
C.    Summarized routes are not accepted.
D.    All imported routes will be automatically summarized when possible.
E.    Only routes with lower administrative distances will be imported.

Answer: B

---

http://www.passleader.com/642-902.html

QUESTION 26
Refer to the exhibit. What is required to complete the IPv6 routing configurations shown? Select the best response.

A.    Interface authentication must be configured.
B.    The routing processes must be configured with an area ID.
C.    IP unicast routing must be enabled.
D.    IPv4 addresses must be applied to the interfaces.

Answer: C

QUESTION 27
When implementing OSPFv3, which statement describes the configuration of OSPF areas? Select the best response.

A.    In interface configuration mode, the OSPFv3 area ID combination assigns interfaces to OSPFv3 areas.
B.    In router configuration mode, the network wildcard area ID combination assigns networks to OSPFv3 areas.
C.    In interface configuration mode, the IPv6 OSPF process area ID combination assigns interfaces to OSPFv3 areas.
D.    In router configuration mode, the IPv6 OSPF interface area ID combination assigns interfaces to OSPFv3 areas.

Answer: C

QUESTION 28
Refer to the exhibit. Routers R1 and R2 have been configured to operate with OSPF. Routers R1 and R3 have been configured to operate with RIP. After configuring the redistribution between OSPF and RIP on R1, no OSPF routes are distributed into RIP. What should be done to correct this problem?

A.    The redistribution command should be reentered with the match route-type parameter included.
B.    The redistribution command should be reentered with the route-map map-tag parameter included.
C.    The redistribution command should be reentered with the metric metric-value parameter included.
D.    Routes will first need to be distributed into another protocol, and then into RIP.

Answer: C

QUESTION 29
When troubleshooting an EIGRP connectivity problem, you notice that two connected EIGRP routers are not becoming EIGRP neighbors. A ping between the two routers was successful. What is the next thing that should be checked? Select the best response.

A.    Verify that the EIGRP hello and hold timers match exactly.
B.    Verify that EIGRP broadcast packets are not being dropped between the two routers with the show ip EIGRP peer command.
C.    Verify that EIGRP broadcast packets are not being dropped between the two routers with the show ip EIGRP traffic command.
D.    Verify that EIGRP is enabled for the appropriate networks on the local and neighboring router.

Answer: D

QUESTION 30
Refer to the exhibit. It is desired to set up a BGP neighbor relationship between routers R1 and R4. BGP packets between them could travel through R2 or R3. What is the simplest configuration that will allow for failover? Select the best response.

A.    Configure BGP neighbor relationships between all interfaces on R1 and R4.
B.    Install a direct connection between R1 and R4.
C.    Configure loopback interfaces on R1 and R4 to provide the update source address for BGP packets.
D.    Configure only one neighbor relationship between R1’s 192.168.1.2 interface and R4’s 172.16.10.2 interface.

Answer: C

---

http://www.passleader.com/642-902.html